Ride1Up LMT'D: parts and specs

Specs are for the stock bike as sold; check your own bike before you buy. This page covers the original Ride1Up LMT'D (v1), sold from 2021 to 2023 in XR and ST frames. The LMT'D V2 uses a different battery, so don't mix the two lists. The v1 was built with either a cadence or a torque sensor, and with an MXUS or AKM motor; the controller, sensor and motor wheel must match your build. Ride1Up sells most parts below from one model parts page and its rear wheel and motor page; both showed in stock with no prices, read Nov 9, 2026.

Parts list

• Tire: WTB Groov-e, 27.5 x 2.4". Tires from 1.75" to 2.4" wide fit; run 30 to 55 psi.
• Inner tube: 27.5" with a width range that covers 2.4", Schrader valve.
• Disc brake caliper: Tektro HD-M285 hydraulic, 180 mm, on the torque sensor version.
• Chain: KMC Z8.3, 8-speed.
• Cassette: Shimano 11 to 32T with a Shimano RD-M370 derailleur, 8-speed Rapidfire Plus shifter and 44T Prowheel chainring. Derailleur, hanger and freehub body are on the parts page.
• Hub motor: 48V 750 W geared rear hub. Ride1Up's rear wheel and motor page lists LMT'D (MXUS) and LMT'D (AKM) as a full wheel or stator only.
• Motor cable and hall sensors: 1000 mm and 300 mm motor cables are on the parts page.
• E-bike controller: 48V 22A Lishui sine-wave. Torque only and cadence only controllers are on the parts page.
• E-bike display: KD218 color display, in ST and XR versions on the parts page.
• Throttle: Left side thumb throttle, in ST and XR versions on the parts page.
• Pedal assist sensor: Torque sensor, or a cadence sensor on cadence builds. Torque sensor, torque sensor cable and ST and XR cadence sensors are on the parts page.
• E-bike charger: 48V, 2 A charger and cable. Confirm the charger option for your bike with Ride1Up before you order.
• E-bike battery: 48V 14Ah Reention Eel Pro with Samsung cells. The LMT'D V1 and Core-5 battery page sells it for $395.00 (in stock, read Nov 9, 2026); it does not fit the LMT'D V2. Batteries are not returnable.
• Battery charge port: A charge port cover is on the parts page.
• E-bike lights: 60 lux front light. The headlight is on the parts page.
• Grips: Ergonomic locking rubber grips.
• Saddle: Selle Royal Freeway Plush Gel on a 31.6 mm, 350 mm seat post.

Tools for common jobs

• Hex keys: caliper, stem, handlebar and seat post bolts.
• Tire levers: changing a tube.
• Floor pump with gauge: setting 30 to 55 psi; see set tire pressure.
• Axle nut wrench: rear wheel removal on the hub motor; see rear hub wheel removal.
• Torque wrench: stem, bar and crank bolts to the values in your manual.
• Brake pad spreader: resetting the Tektro pistons before new pads.
• Brake bleed kit: bleeding the Tektro HD-M285 brakes with mineral oil; see bleed Tektro brakes.
• Chain checker: measuring KMC Z8.3 chain wear.
• Multimeter: testing charger output at its plug; see check your charger.

Where to buy

• Ride1Up's LMT'D (v1) replacement parts page, LMT'D V1 and Core-5 battery page and rear wheel and motor page.
• Independent sellers: parts suppliers.
• A shop can order and fit parts: find a shop.

Common repairs

• LMT'D error codes
• Ride1Up troubleshooting and e-bike error codes
• Error 30 communication error, error 21 power cuts on hills and error 23 or 24 after wheel removal
• Brake sensor stops motor power
• Replace disc brake pads, bed in disc brakes and fix a spongy brake lever
• Fix a flat on a rear hub motor wheel and no pedal assist

Sources

• ride1up.com
• parts page, ride1up.com
• LMT'D V1 and Core-5 battery page, ride1up.com
• rear wheel and motor page, ride1up.com
• support.ride1up.com
• ride1up.com

Stuck after these checks? Find a shop near you.