E-bikes
Lectric eBikes
Repair guides, troubleshooting and the official manuals for Lectric eBikes. Pick your model for everything that applies to it.
Lectric eBikes guides
- Lectric eBikes troubleshooting: common problems and safe checksTroubleshootingSafe checks for common Lectric eBikes problems, including a bike that won't power on, E007 and E008 errors, noisy brakes and battery care, plus when to get a pro.
- Lectric XP 1.0 and XP 3.0: E008 on the display means different thingsTroubleshootingE008 on a Lectric XP is a throttle fault in the original XP manual but a display communication fault in the XP 3.0 manual. Check the right quick plug for your model first.
- Lectric XP 3.0, XP Lite and XPedition: charger light stays red or never lightsTroubleshootingIf your Lectric charger light never turns on, check the cord and outlet. If it stays red and never turns green, Lectric's manuals say the battery pack may be defective. Here is what to check safely.
- Lectric XP 3.0: mechanical disc brakes losing stopping powerTroubleshootingSome Lectric XP 3.0 bikes sold from late 2022 to May 2023 have recalled mechanical brake calipers that can lose braking power. Check the recall first, then do normal brake checks.
- Lectric XP 3.0: parts and specsReferenceReplacement parts and specs for the Lectric XP 3.0: 20 x 3 tires and tubes, Type B or Type D pads by brake type, the hydraulic upgrade kit, 180 mm rotors, 7-speed freewheel, charger and batteries, with Lectric's prices.
- Lectric XP, XP Lite and XPedition: E007 motor fault on the displayTroubleshootingE007 on a Lectric display is a motor fault. Start with the motor quick plug near the right side of the rear axle, then the controller connections, and know when it is a cable, motor or controller job.
- Lectric XP, XP Lite and XPedition: won't turn on, display stays blankTroubleshootingA Lectric that won't power on usually needs a charge, the battery key turned on, or the display quick plug reseated. Here are Lectric's own steps, in order, and when to call support.
- Lectric XP4, XPeak 2 and XP Trike 2: E003 pedal assist sensor faultTroubleshootingE003 on the XP4, XPeak 2 and XP Trike 2 is a PAS sensor fault. Check the PAS quick plug first, then the sensor and magnet ring at the crank, before replacing the sensor.
- Lectric XP4, XPeak 2 and XP Trike 2: E006 battery undervoltage, bike stops helpingTroubleshootingE006 on the XP4, XPeak 2 and XP Trike 2 means battery undervoltage. Lectric's fix is a full charge. If E006 returns soon after charging, check the charger light, because a light that stays red can mean a worn battery.
- Lectric XP4, XPeak 2 and XP Trike 2: E010 or E011 display communication failureTroubleshootingE010 and E011 on the XP4, XPeak 2 and XP Trike 2 mean the display isn't receiving from or sending to the controller. Lectric's fix is the display quick plug, then a shop for the display or controller.
- Lectric XP4, XPeak 2 and XP Trike 2: error codesReferenceThe codes Lectric lists for the XP4, XPeak 2.0 and XP Trike 2: E003 to E011 and HOT, what each means and which quick plug to check first.
Models
- Lectric ONEE-bike
- XP 1.0E-bike, 3 model guides
- XP 2.0E-bike, 2 model guides
- XP 3.0E-bike, 6 model guides
- XP 4E-bike, 4 model guides
- XP LiteE-bike, 3 model guides
- XP Lite 2.0E-bike
- XP Lite 3E-bike
- XP TrikeE-bike
- XP Trike 2E-bike, 4 model guides
- XP4 LEE-bike
- XPeakE-bike
- XPeak 2E-bike, 4 model guides
- XPeditionE-bike, 3 model guides
- XPedition 2E-bike
- XPremiumE-bike
- XPressE-bike
- XPress 2 CommuterE-bike
- XPress 2 CruiserE-bike
- XPress LiteE-bike
Troubleshooting that applies to most models
- Battery dies fast or range droppedTroubleshootingYour e-bike used to go further on a charge. How to tell normal wear and riding conditions from a battery or charger problem.
- Battery won't chargeTroubleshootingThe charger light doesn't change or the battery won't go up. Safe checks on the charger, the outlet and the port, and when to stop.
- Clicking, grinding or squeaking noisesTroubleshootingWhere e-bike noises usually come from: the chain and gears, the brakes, loose bolts, the cranks and bearings, or the motor.
- Display blank, flickering or frozenTroubleshootingThe handlebar display won't show anything, flickers or freezes. Usually a plug, the battery, water or the display itself.
- Display works but no pedal assistTroubleshootingThe display turns on, but the motor doesn't help when you pedal. Check the assist level, the speed sensor and the brake cut-offs.
- E-bike error codes: what they mean and what to try firstTroubleshootingYour e-bike display shows an error code. Here's how to read it, the safe things to try yourself, and where to find your system's official code list.
- E-bike or scooter won't turn onTroubleshootingNothing happens when you press the power button. Work through the battery, the key and the plugs before assuming the worst.
- Motor cuts out or power comes and goesTroubleshootingThe motor stops helping on and off, over bumps or on hills. Usually a loose connection, a brake sensor, heat or a tired battery.